Mac mini ssd kit ifixit

Arctic Silver ArctiClean. Precision Tweezers Set. Heavy Duty Spudger. This site uses cookies. By continuing to use this site you agree to our use of cookies in accordance with our cookies policy. More information x. Product code: EU Choose variant Part Only Fix Kit.

Adding SSD as 2nd drive. - Apple Community

Ready for shipping. Newsletter Join , other smart people reading our repair newsletter!

About the Author

Invalid email. Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case. Remove the two Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case.

5 Categories

Removing the standoff screw is not necessary to remove the fan. You need only raise the fan enough to lift it off the standoff screw. Grab all the wires at once and gently pull straight up to disconnect the fan from the logic board.

  1. Mac mini Teardown: User-Upgradeable RAM, But Soldered Down CPU and Storage - MacRumors?
  2. Max out your Mac Mini..
  3. mountain house chili mac can;
  4. correction automatique word 2008 mac;

Do not pry at the socket, or you may rip it from the logic board. It can be difficult to get the hard drive seated correctly such that the antenna plate fits in place correctly.

If the screw holes don't line up with those on the hard drive, make sure that the two pins that are in the back of the hard drive are properly seated in the holes at the back of the case, above the housing for the second hard drive. The antenna attaches directly to the hard drive red markers , therefore attaching the antenna can move the hard drive around and loosen the connection of the hard drive cable to the logic board. Do not remove the antenna plate yet. Use the flat end of a spudger to pry the hard drive connector up from its socket on the logic board.

  1. assassins creed 2 mac controls.
  2. Upgradeable;
  3. wireless karaoke microphone for mac.

Use the tip of a spudger to lift the IR sensor connector up and out of its socket on the logic board. To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red.

Device Info

Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board. Be sure it makes contact with the top side of outer case below the logic board before proceeding. Pull the hard drive away from the front edge of the mini and remove it from the outer case. Remove the hard drive cable by pulling its connector straight away from the hard drive.

Mac mini Late 2014 Hard Drive Replacement

There may be a sticker connecting this cable to the hard drive. If so, remove the sticker before attempting to remove the cable! If you are installing a new hard drive, we have an OS X install guide to get you up and running.

Late 2018 Mac Mini Teardown & Ram Upgrade + Re-assembly

Cancel: I did not complete this guide. Badges: Very helpful guide, thanks! As many have said before, I would not detach the fan or antenna, just move it out of the way. One very trivial tip: slide a piece of paper over the logic board as soon as you've removed the fan, as a protection against accidentally touching the components with your fingers or tools. I did not reinstall the plastic cover on the HDD. Dismantling the Mini was simple, but the two hardest steps when installing a new hard drive were sliding the drive back in aligned correctly, and replacing the antenna grill.

Even with the logic board pushed out, I found it difficult to line up the screws on the hard drive and get it seated properly. As for the grill, it would not line up with the screw holes. I had to use the Mac Mini tool hooked into a hole in the grill as a lever to lift it up and in towards the lip of the rim it was sitting on.

There was an audible snap as it settled into place. I've done about a dozen mac mini to SSD upgrades over the past few years but I've only owned a logic board removal tool for my latest upgrade. I was struggling to get the drive pegs into the grommet, and the usual 'turn it upside down and giggle it around' trick just wasn't working for me. I tried getting a spudger underneath the drive to lift it up into the grommet holes but there wasn't enough clearance to get any leverage.

Mac mini Unibody SSD Upgrade Bundle

I used the mini opening tool with one end underneath the drive, and the center portion sticking out perpendicular to the motherboard I'll add a picture to lift the drive up and into place. THANK you so much for the idea to use the logic board removal tool. Help Translate iFixit. Difficulty Moderate.